Amorphous Alloy Transformer Distribution

Product technical performance
amorphous alloy transformer
Amorphous alloy material is a new type of magnetic material that came out in the 1970s. It is an alloy of iron and boron. The molten alloy liquid is sprayed onto a high-speed rotating cryogenic roller at a rapid rate of 106°C/s. Cooling causes the alloy to be less than crystalline to form an amorphous alloy material. The amorphous alloy material has a very small magnetization energy, so its hysteresis loss is very low. Due to the high resistivity of the amorphous alloy strip, the single piece thickness Only 0.02mm, so its eddy current loss is also very small.
Amorphous alloy transformer is an energy-saving and low-loss power transformer with excellent performance. It uses amorphous alloy material instead of silicon steel sheet to make iron core. It features low no-load loss and small no-load current. Amorphous alloy transformer compared with the traditional silicon steel core transformer ("9" type), no-load loss can be reduced by 70% to 80%, no-load current drop of about 30%. This will not only effectively ease power shortages, but also save limited resources. Therefore, amorphous alloy transformers have gained more and more attention in our country.
The company is an early manufacturer of amorphous alloy transformers in China. In 2000, it passed the National Transformer Supervision and Inspection Center to test and obtain the Anhui Provincial Identification Report. In recent years, absorbing advanced technologies and processes at home and abroad, and optimizing design, the structure of the products has become more rational, and the noise performance, electrical strength, mechanical strength, and heat dissipation capacity of the products have been significantly improved. They have been widely used in three-phase, 50Hz, and 10KV. In the power system, it is the main power equipment for 10KV power grids for industrial and agricultural distribution, power and lighting.
The structural characteristics of the company's 10KV amorphous alloy distribution transformer:
l Iron core: Iron chip adopts imported amorphous alloy silicon steel sheet. The iron core adopts three-pillar or five-post multi-step joints. The clamping method adopts self-weight and silicon plate fixed in the grooved clamps, not only Amorphous iron core is fixed, and effectively reduce noise;
l Coil: Paper-coated flat copper wire or copper foil made of high-quality oxygen-free copper is used for low-voltage wires, and paper-coated flat copper wire or enameled round copper wire made of high-quality oxygen-free copper is used for high-voltage wires. The coils are directly wound in a rectangular structure. And after vacuum impregnation treatment, greatly improve the mechanical strength of the coil;
l Fuel tank: The fuel tank adopts a fully-sealed barrel structure, and the heat-dissipation element is a corrugated plate radiator. The bottom of the box is welded with a base that conforms to the national standard gauge, which is convenient for the user to install;
l Safety protection device: In accordance with national standards and user requirements, the transformer can be configured with pressure release valves, gas relays, signal thermometers, oil sample valves and other safety protection devices.
Use environment:
1. Altitude: ≤1000 meters;
2.The ambient temperature:
The highest temperature +40 °C, the highest monthly average temperature +30 °C;
The lowest temperature is -10°C, the highest annual average temperature is +20°C;
Installation environment: The inclination of the installation site is ≤ 3° without any obvious contamination and corrosion flammable gas.
a. Technical standards
The company's production of 10KV amorphous alloy distribution transformers follows the following standards:
GB1094.1-1996 GB1094.2-1996                    
GB1094.3-2003 GB1094.5-2008
GB1094.10-2003 GB1094.11-2007                 
JB/T10318-2002 GB/T10237-1988
JB/T10088-2004 GB311.1-1997





b. Technical data sheet
Why shenhong?
Δ  26 years of manufacturing experience
Δ  Qualified supplier of SGCC(State Grid Corporation of China)
Δ  Providing 24 months warranty period
Δ  Annual production capacity of 10 million kVA
Δ  Equal or higher than IEC international standard
Δ  One of the first 15 companies successfully listed on the Anhui Stock Exchange Trust Center on September 30, 2013
Δ  Certified as a national high-tech enterprise in 2008
Δ  With independent research and development, design, production capacity
Δ  ISO9001/ISO14001 certified

Service
Δ Delivery date: Usually it will take about 15-30 days according to the order;
Δ Payment: 30% TT in advance,and the balance before shippment;
Δ Package: strong fumigation plywood case for sea transportaion.